2 Truck Upfitters 16" Gas Props (15.7" Extended, 9.4" Compressed, 38 pounds of Pressure ea) for are, ATC, Snugtop, Leer Camper Shell/Truck Cap Rear Door. Measurement Required! Incl 4 Ball mounts!

★★★★★ 4.8 131 Bewertungen

€12.00
Preis bei Onlinekauf
Kostenloser Versand 30 Tage kostenlose Rückgabe

Verkauft und versendet von www.castellidiario.com.ar
Wir bemühen uns, Ihnen genaue Produktinformationen anzuzeigen. Hersteller, Lieferanten und andere stellen die hier gezeigten Angaben bereit.
€12.00
Preis bei Onlinekauf
Kostenloser Versand 30 Tage kostenlose Rückgabe

Wie möchten Sie Ihren Artikel erhalten?
Die ersten 30 Tage sind kostenlos! Wählen Sie den Tarif an der Kasse.
Versand
Ankunft 21.11.
Kostenlos
Abholung
In der Nähe prüfen
Lieferung
Nicht verfügbar

Verkauft und versendet von www.castellidiario.com.ar
30 Tage kostenlose Rückgabe Details

Produktdetails

Artikelnummer 217737820 Erscheinungsdatum 2026/04/19 Listenpreis €12.00 Modellnummer 217737820
Kategorie
  • CHECK LENGTHS AND PRESSURE BEFORE ORDERING. THESE DO NOT FIT ALL CANOPY and COVERS! THE MEASUREMENTS ARE FROM CENTER OF BALL MOUNT TO CENTER OF BALL MOUNT, NOT FROM END TO END OF STRUT! SEE PICTURE! Use a measuring tape to measure the door gas strut that you are replacing. Measure from the CENTER of the gas prop head (little plastic end), to the other side. DO NOT measure from the end of the gas prop, your measurement will be too long. Note that most applications allow for 1-5% size variation.
  • Truck Upfitters Pair of 38 pound (each) gas struts. 15.7" extended length and 9.4" compressed length. This size of door shock absorber is for tall medium weight rear or side camper shell doors. Each canopy shock has 38 lbs of pressure, for a total of 76 lbs of pressure. Please note that this does not mean that it can lift something that is 76 lbs. the typical hinged-style door weight for this prop is approximately 50-70 lbs, including the weight of the camper shell locks and keys.
  • These gas lift cylinders do not fit all truck cap/camper shell brands/models. Measure your strut from center of socket to center of socket when fully opened & fully closed to get accurate measurement. See pictures to determine how to measure. Do NOT measure from end to end. Measurement must be from the center of plastic ball mount on each end of the gas spring lift. Measurement is important to ensure they open properly and get a good camper shell seal against the camper shell gasket when closed.
  • Comes with four 10mm ball mounts for alternate 'other than truck camper shell' applications, such as in camper / canopy windoors, RV doors and awnings, boat hatch spring lifts, gas struts for cabinets, storage bed lifts, toolbox struts, etc. These gas shock lift supports CANNOT be compressed by hand. These gas props MUST be installed in the EXTENDED / OPEN position. It is nearly impossible to install them in the CLOSED position. Please refer to the install video for guidance on how to install.
  • Equivalent to Suspa # c16-09209 or Stabilus # 01824. These camper shell shocks are compatible with many truck canopy types, including LEER truck cap parts, ARE truck topper parts, Glasstite parts, Century parts, Snugtop replacement parts Astro tops, ATC campers, and many other fiberglass brands that utilize gas shocks / gas springs / gas lift cylinders. Compatible with many gas lift brands, including stabilus, lift o mat, and Suspa. These are OEM quality and perfect fit for your topper!

Korrektur der Produktinformationen

Wenn Sie Unvollständigkeiten oder Fehler in den Produktinformationen auf dieser Seite bemerken, nutzen Sie bitte das Korrekturformular unten.

Korrekturanfrage

Kundenbewertungen

4.8 von 5
★★★★★
131 Bewertungen | 54 Rezensionen
So wird die Artikelbewertung berechnet
Alle Bewertungen anzeigen
5 Sterne
87% (114)
4 Sterne
2% (3)
3 Sterne
1% (1)
2 Sterne
0% (0)
1 Stern
10% (13)
Sortieren nach

Für dieses Produkt liegen derzeit keine schriftlichen Bewertungen vor.