953-1A-12DG-2 12VDC 5-Pin PCB Power Relay, 1 Form A (SPST-NO) 30A 250VAC/30VDC, Sealed — Compatible with HSINDA 953G Footprint, HVAC Furnace Blower Compressor Appliance Control Board

★★★★★ 4.8 96 Bewertungen

€4.00
Preis bei Onlinekauf
Kostenloser Versand 30 Tage kostenlose Rückgabe

Verkauft und versendet von www.castellidiario.com.ar
Wir bemühen uns, Ihnen genaue Produktinformationen anzuzeigen. Hersteller, Lieferanten und andere stellen die hier gezeigten Angaben bereit.
€4.00
Preis bei Onlinekauf
Kostenloser Versand 30 Tage kostenlose Rückgabe

Wie möchten Sie Ihren Artikel erhalten?
Die ersten 30 Tage sind kostenlos! Wählen Sie den Tarif an der Kasse.
Versand
Ankunft 24.11.
Kostenlos
Abholung
In der Nähe prüfen
Lieferung
Nicht verfügbar

Verkauft und versendet von www.castellidiario.com.ar
30 Tage kostenlose Rückgabe Details

Produktdetails

Artikelnummer 237383997 Erscheinungsdatum 2026/07/10 Listenpreis €4.00 Modellnummer 237383997
Kategorie

953-1A-12DG-2 Sealed PCB Power Relay — Compatible with HSINDA 953G Footprint A high-capacity 12VDC coil, 5-pin, 1 Form A (SPST-NO) power relay designed for HVAC, appliance and industrial control boards. Use this part when your control PCB calls for the HSINDA 953G sealed 5-pin footprint with two common terminals. Key SpecsContact form: 1 Form A (SPST-NO), Ag-alloy contactsRatings (resistive): up to 30A at 250VAC or 30VDC (max switching: 250VAC / 30VDC)Coil: 12VDC (≈0.9W), resistance ~155 Ω, nominal current ≈77 mAOperate / release time: ≤15 ms / ≤10 msElectrical life: 1×105 ops; mechanical life: 1×107 opsPins / footprint: 5-pin with two common terminals (low-resistance path)Body size: approx. 27.4 × 31.8 mm; sealed housing; RoHSOperating temp: −40 °C to +85 °CTypical ApplicationsCompatible with HSINDA 953G-footprint relay positions on HVAC control boards (compressor, blower, heater)Appliance and industrial control PCBs: pumps, chargers, general motor controlInstallation NotesPower down and discharge capacitors; observe ESD precautions.Desolder the original relay and clean the pads.Insert this unit per board silkscreen/orientation; solder all five pins and inspect joints.Verify coil drive polarity if a diode/transistor driver is used; confirm creepage/clearance.Functional test under load; reapply conformal coating if the board requires it.Compatibility ChecklistBoard calls for “953-1A-12DG-2” or “953G 1A 12V sealed”5-pin, two-common-terminal footprint matches the PCB through-holesCoil 12VDC; contact form 1A (NO); load within ≤30A at 250VAC / ≤30VDC (resistive)Envelope and height fit the enclosure; pick-up voltage requirement ≤9VIn the box: 1 × 953-1A-12DG-2 relay

  • Parameters & footprint — Sealed PCB power relay 953-1A-12DG-2 (953G series): coil 12VDC (≈0.9W), coil resistance 155 Ω, nominal coil current ≈77 mA, pick-up ≤9 V, drop-out ≥1.2 V; contact arrangement 1 Form A (SPST-NO) up to 30 A resistive at 250 VAC or 30 VDC (max switching 250 VAC/30 VDC); Ag-alloy contacts; electrical life 100k ops, mechanical life 10M ops; two common terminals / 5-pin layout for low contact resistance; body ~27.4 × 31.8 mm; RoHS. Compatible with HSINDA 953G sealed 5-pin footprints on control boards.
  • Installation & location — PCB-mounted relay typically located on HVAC/appliance/industrial control boards (e.g., compressor, blower, heater, pump, charger outputs). To install: desolder the original relay, clean pads, insert this unit per silkscreen notch/orientation, solder all 5 pins, and inspect joints; observe coil polarity if the driver uses a diode or transistor; maintain creepage/clearance around high-voltage pins; typical board designators include “RL1/RLY1/953.” Compatible with control-board locations calling for a sealed 12 VDC 1 Form A 30 A relay of the HSINDA 953G footprint
  • Compatibility checklist (use to confirm fit) — Compatible with boards that specify 953-1A-12DG-2 or “953G 1A 12V sealed” and that use the 5-pin two-common-terminal footprint shown in the 953G outline. Match the following before purchase: coil 12 VDC (≈77 mA), contact form 1A (normally open), load ≤30 A at 250 VAC or ≤30 VDC (resistive), outline ~27.4 × 31.8 mm, engage height/clearance, and pick-up ≤9 V. If your original part is 953-1C (SPDT) or 953-1A-12DG-1 (4-pin), it is not a drop-in; choose the identical contact arrangement and pin count for your board. Compatible with the HSINDA 953G sealed footprint only.
  • Reliability & related items — Coil class options and sealed housing support harsh environments; operate time ≤15 ms, release ≤10 ms; dielectric strength test levels support robust isolation. For longevity on inductive loads, size margins conservatively and add suppression (e.g., flyback diode/TVS across coil or snubber across load if your board lacks it). Compatible with common control-board service materials (rosin flux, solder wick) and with maintenance practices such as conformal-coating rework where required. Operating range −40 °C to +85 °C; store dry and within temperature limits.
ASIN B0FZ4L7M88
Brand Name Kwaich
Part Number 953-1A-12DG-2-434-1
Coil Voltage 12 Volts (DC)
Contact Type Normally Open
Manufacturer RZ
Mounting Type PCB Mount
Connector Type 5-pin
Current Rating 30 Amps
Coil Resistance 155 Ohms
Contact Material Silver Alloy
Specification Met RoHS
Contact Current Rating 30 Amps
Upper Temperature Rating 85 Degrees Celsius
Maximum Switching Current 30 Amps
Maximum Switching Voltage 250 Volts (AC)

Korrektur der Produktinformationen

Wenn Sie Unvollständigkeiten oder Fehler in den Produktinformationen auf dieser Seite bemerken, nutzen Sie bitte das Korrekturformular unten.

Korrekturanfrage

Kundenbewertungen

4.8 von 5
★★★★★
96 Bewertungen | 39 Rezensionen
So wird die Artikelbewertung berechnet
Alle Bewertungen anzeigen
5 Sterne
87% (84)
4 Sterne
2% (2)
3 Sterne
1% (1)
2 Sterne
0% (0)
1 Stern
10% (10)
Sortieren nach

Für dieses Produkt liegen derzeit keine schriftlichen Bewertungen vor.