ENGINE BLOCK HEATER Pan 3M stick on Pad (120V U.S.A. / Long CORD) Designed for: 4 Cylinder Engines by Z-TOOL HEATER TEC.

★★★★★ 5.0 111 Bewertungen

€11.29
Preis bei Onlinekauf
Kostenloser Versand 30 Tage kostenlose Rückgabe

Verkauft und versendet von www.castellidiario.com.ar
Wir bemühen uns, Ihnen genaue Produktinformationen anzuzeigen. Hersteller, Lieferanten und andere stellen die hier gezeigten Angaben bereit.
€11.29
Preis bei Onlinekauf
Kostenloser Versand 30 Tage kostenlose Rückgabe

Wie möchten Sie Ihren Artikel erhalten?
Die ersten 30 Tage sind kostenlos! Wählen Sie den Tarif an der Kasse.
Versand
Ankunft 20.11.
Kostenlos
Abholung
In der Nähe prüfen
Lieferung
Nicht verfügbar

Verkauft und versendet von www.castellidiario.com.ar
30 Tage kostenlose Rückgabe Details

Produktdetails

Artikelnummer 228313816 Erscheinungsdatum 2026/05/31 Listenpreis €11.29 Modellnummer 228313816
Kategorie

WARNING ::::::: Personal Injury: Avoid touching the heater while it is energized MOUNTING AND INSTALLATION: Step 1: The pad heater must be installed on a flat, uniform surface with 100% of the heater surface in contact with the object being heated. Step 2: If intended application area is painted, paint must be removed prior to installation. The temperatures associated with heater operation can cause paint to crack causing the heater to delaminate from applied surface. Step 3: To obtain adhesion, the bonding surfaces must be clean and dry. Some recommended surface cleaning solvents are isopropyl alcohol or heptane. The solvent must be non-oil based. Step 4: Plug the pad heater in for a short time (about 5 seconds) to warm the adhesive. Step 5: Slowly remove the cover on the heater to expose the pressure sensitive adhesive. Orient the heater as desired and apply it to the selected surface. Apply pressure to the entire heater with a roller to eliminate potential air gaps. Step 6: Once applied to desired surface, energize heater for a short time (about 30 seconds). De-energize heater and again apply pressure. Step7: Use the wire ties provided to secure the power cord in a manner that isolates the cord from hot surfaces and provides strain relief. WARNING ::::::: Personal Injury: Avoid touching the heater while it is energized

  • Z-TOOL HEATER TEC. ------ STICK TO CLEAN SURFACE OF OIL PAN ( See Pictures)
  • Z-TOOL HEATER TEC. Cold weather to make sure your engine starts. Make starting faster and easier in cold weather. Provide heat to the cabin much faster. Reduce the wear on your engine during cold weather starts! They plug into a standard electrical outlet and can be put onto a timer, or a temperature triggered electrical outlet. This in effect causes your engine to reach operating temperature much faster and gives you heat inside the cabin much faster as well.
  • On top of the benefit of heating up quicker, it also saves your engine a ton of wear and tear on internal moving parts! When an engine is warm it starts easier, when its cold it is very hard on your engine.
  • Designed for: 2WD 4x4 AWD vehicles w/ 4 Cylinder Engines. Long 4.5 ft Cord
  • ATTACH TO TIMER FOR $ SAVINGS
ASIN B07H4WKQKD
Brand APSG
Exterior Smooth
Item Weight 8 ounces
Manufacturer Z-TOOL HEATER TEC / APSG
Package Dimensions 9.5 x 4 x 0.9 inches
Manufacturer Part Number HEATER PREMIUM#7862
Is Discontinued By Manufacturer No

Korrektur der Produktinformationen

Wenn Sie Unvollständigkeiten oder Fehler in den Produktinformationen auf dieser Seite bemerken, nutzen Sie bitte das Korrekturformular unten.

Korrekturanfrage

Kundenbewertungen

5 von 5
★★★★★
111 Bewertungen | 46 Rezensionen
So wird die Artikelbewertung berechnet
Alle Bewertungen anzeigen
5 Sterne
90% (100)
4 Sterne
0% (0)
3 Sterne
0% (0)
2 Sterne
0% (0)
1 Stern
10% (11)
Sortieren nach

Für dieses Produkt liegen derzeit keine schriftlichen Bewertungen vor.