Infrared Paint Curing Lamp,2000W 110V Shortwave Infrared Paint Baking Lamp w/Telescopic Bracket & Timing Function,Paint Dryer for Car Bodywork Repair

DetailsHandlebar: The design of the handlebar increases its portability while also allowing your paint to be cured everywhere.Screw Holes and Slide Rails: It has screw holes on both sides to allow you to install the appropriate brackets as needed for your convenience. The design of the slide rail also allows you to combine 2 or more infrared paint-curing lamps.Net Cover: The net cover is made of high-gloss chrome, which is not easy to rust while its proper grid spacing will not cut the efficiency of the infrared paint-curing lamp.ApplicationIt can be used for automotive painting, field maintenance, engine drying, stripping, putty drying, primer drying, partial paint drying, or preheating before painting.Installation1. Mounting Base: Remove the nuts manually. Adjust the bolt to the middle position, align the two holes on the base and place nuts, then tighten the nuts.2. Mounting Connection Plate: Align the female through holes in the connection plate with the holes on either side of the mounting plate. Tighten the nuts to ensure the connection plate is perpendicular to the mounting plate.3. Connection Bracket: Remove the swivel nut at the top of the bracket, align the hole in the middle of the connection plate, and tighten the nut.4. Height Adjustment: The free retraction of height is achieved by two rotating devices on the bracket.SpecificationModel: DT-SC-003Color: Yellow, BlackPlug Standard: American EU Energy Label Efficiency Labeling Class: A++to EEfficiency: EVoltage: 110VPower: 2000WWorking Temperature: 0-200°CWorking Angle: 0-270°Maximum Baking Area: 42*50cm/ 16.54*19.69inMaterial: AluminumBulb Type: Halogen (Included)Lamp Length: 27cm/ 10.6inBaking Lamp Size: 41.5*7*19cm/ 16.3*2.8*7.5inTotal Height Range: 65-152cm/ 25.59-59.84inPackage Size: 62*34*19cm/ 24.41*13.39*7.48inNet Weight: 4.9kg/ 10.8lbsGross Weight: 5.1kg/ 11.24lbsPackage Included1* Baking Lamp1* Handlebar1* Telescopic Bracket1* Connecting Plate1* Fixing Plate2* Hexagonal WrenchesAll Accessories for AssemblyNotes1. Please note that minors are not allowed to touch to prevent burns!2. Please allow the slight color difference caused by the shooting light and 1-3 cm error due to manual measurement, and make sure you do not mind before ordering.

• 【High Efficiency】:Its working temperature can reach 200℃, and it uses a special internal high-reflectivity reflector to make the heat more evenly distributed, which can increase the curing area (16.54*19.69in) and reduce the curing time
• 【Timer Function】:You can set the time of curing within 0-90 minutes by turning the knob on the back of the light according to the paint surface, which is convenient for you
• 【Height and Angle Adjustable】:We equip you with a telescopic stand, you can adjust its height between 25.59-59.84 by adjusting the two knobs on the stand according to your needs. And you can manually adjust its working angle up to 270°
• 【Short-wave Infrared Heating】:This infrared coating curing lamp utilizes short-wave infrared curing technology, combining high luminous efficacy with strong penetration. This heating method enables drying from the inside out, resulting in a cured paint surface with high gloss and strong adhesion. It also significantly reduces wrinkling and cracking, eliminating the need for rework
• 【High Safety】:It will automatically shut down at the end of the timer, so you don't have to worry about the safety hazards caused by its long and hot operation